Volumetric change of flowable composite resins due to polymerization as measured with an electronic mercury dilatometer

Simple item page
dc.contributor.authorMulder, Riaan
dc.contributor.authorGrobler, Sias Renier
dc.contributor.authorOsman, Yusuf Ismail
dc.date.accessioned2014-08-05T20:26:06Z
dc.date.available2014-08-05T20:26:06Z
dc.date.issued2013
dc.description.abstractBACKGROUND: To determine the total volumetric change and the relative speed of shrinkage of bulk fill flowable composites during polymerization. MATERIALS AND METHODS: A specially designed electronic mercury dilatometer was used to determine the volumetric change. The light intensity was 500mW/cm2. The mercury dilatometer measured the volumetric change every 0.5 seconds during the 35 second irradiation exposure time. The materials tested were Z250 as standard and control. Four bulk fill flowable composites were tested. RESULTS: The sequence of total volumetric change was found to be: Z250 < Filtek bulk fill < Xtra-Base bulk fill < SDR < Venus bulk fill. The speed of shrinkage of the bulk fill flowables was faster than that of Z250, while the 2 flowables with the highest shrinkage speed (SDR and Venus) also had the highest total volumetric change. Of the different materials tested the volumetric change of Z250 (1.13%) was the lowest and significantly less (p<0.05) than that of SDR (1.55%) and Venus (1.72%). The material with the highest filler content (Z250) also showed the lowest shrinkage (1.13%) but this effect could not be seen in the flowables. In general, it was found that a 35 second irradiation period (with a light intensity of 500mW/cm2) was satisfactory for complete polymerization of the resins. CONCLUSIONS: The volumetric changes and speed of shrinkage were higher for all 4 bulk fill flowable composites than for Z250. SDR and Venus flowables had the fastest and highest volumetric shrinkage. Clinical significance: The manufacturers of bulk fill flowable composites advocate filling layers of 4mm. However, because of the high shrinkage values found in this study it should be suggested that the standard 2mm layer increments still be used.en_US
dc.description.accreditationWeb of Scienceen_US
dc.description.sponsorshipIt was partly supported by the IADR and the C. H. Pameijer Fellowship 2012.en_US
dc.identifier.citationMulder, R., Grobler, S.R. & Osman, Y.I. (2013). Volumetric change of flowable composite resins due to polymerization as measured with an electronic mercury dilatometer. Oral Biology and Dentistry. 1:1en_US
dc.identifier.issn2053-5775
dc.identifier.urihttp://hdl.handle.net/10566/1152
dc.language.isoenen_US
dc.privacy.showsubmitterfalse
dc.publisherHerbert Publications Ltd.en_US
dc.rights© 2013 Mulder et al; licensee Herbert Publications Ltd. This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/3.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
dc.source.urihttp://dx.doi.org/10.7243/2053-5775-1-1
dc.status.ispeerreviewedtrue
dc.subjectVolumetric changeen_US
dc.subjectFlowable compositesen_US
dc.subjectMercury dilatometeren_US
dc.subjectBulk fillen_US
dc.subjectFlowable composites
dc.titleVolumetric change of flowable composite resins due to polymerization as measured with an electronic mercury dilatometeren_US
dc.typeArticleen_US

Files

Original bundle
Now showing 1 - 1 of 1
Thumbnail Image
Name:
MulderVolumetricChange2013.pdf
Size:
684.32 KB
Format:
Adobe Portable Document Format
Description:
Published version
Download
License bundle
Now showing 1 - 1 of 1
No Thumbnail Available
Name:
license.txt
Size:
1.55 KB
Format:
Item-specific license agreed upon to submission
Description:
Download

Collections

Research Articles (Orthodontics)
Prof. Riaan Mulder
Prof. Yusuf Osman